Study of the influence of thermal annealing process on the morphological and structural properties of Sb2Se3 thin films

Authors

  • К.М. Кучкаров Физико-технический институт им. С.А. Азимова АН РУз
  • Б.А. Эргашев Физико-технический институт им. С.А. Азимова АН РУз
  • Д.З. Исаков Физико-технический институт им. С.А. Азимова АН РУз
  • Р.Р. Хуррамов Физико-технический институт им. С.А. Азимова АН РУз
  • М. Тиванов Белорусский государственный университет
  • Р.Р. Юлдашов Физико-технический институт им. С.А. Азимова АН РУз
  • М.А. Махмудов Физико-технический институт им. С.А. Азимова АН РУз
  • А.C. Ачилов Физико-технический институт им. С.А. Азимова АН РУз
  • M.П. Пиримматов Физико-технический институт им. С.А. Азимова АН РУз
  • Ш. Бобомуродов Физико-технический институт им. С.А. Азимова АН РУз
  • A. Матмурадов Физико-технический институт им. С.А. Азимова АН РУз
  • A. Эшкораев Физико-технический институт им. С.А. Азимова АН РУз

DOI:

https://doi.org/10.52304/.v28i3.663

Keywords:

chemical molecular beam deposition (CMBD), Mo substrate, thin films, SEM, XRD, Raman spectroscopy

Abstract

This study comprehensively investigates the effect of thermal annealing on the morphological and structural properties of Sb2Se3 thin films obtained on glass substrates using chemical molecular beam deposition (CMBD). The samples annealed in air at 200°C for 10, 20, and 30 min. Energy-dispersive X-ray spectroscopy (EDS) showed that the film composition was close to stoichiometric, with a slight decrease in Se content observed with increasing annealing time. SEM and AFM analysis revealed that thermal annealing increased film density, reduced porosity, and smoothed the surface. XRD results confirmed that all samples correspond to the orthorhombic phase of Sb2Se3, with the sample annealed for 10 minutes exhibiting a preferential orientation of the (211), (221), and (002) planes, which are favourable for charge carrier transport. Raman spectroscopy revealed the presence of secondary phases (Se and Sb) in unannealed films, while the annealing process leads to their gradual disappearance. These results indicate that annealing at 200°C improves the structural perfection of Sb2Se3 thin films, increases surface homogeneity, and completely removes secondary phases.

Published

2026-10-22

How to Cite

Кучкаров, К., Эргашев, Б., Исаков, Д., Хуррамов, Р., Тиванов, М., Юлдашов, Р., Махмудов, М., Ачилов, А., Пиримматов M., Бобомуродов, Ш., Матмурадов A., & Эшкораев A. (2026). Study of the influence of thermal annealing process on the morphological and structural properties of Sb2Se3 thin films. “Uzbek Journal of Physics”, 28(3). https://doi.org/10.52304/.v28i3.663

Issue

Section

05. Optics and Spectroscopy. Laser Physics. Nonlinear Optics

Most read articles by the same author(s)